03 Jun 2019
Best 15 Brass Wood Screws
#2×1/2″ PHIL FLAT HEAD Brass Wood Screw (100/box) - Tensile strength 50,000, 60,000 psi. Head height 0123″. Screws, solid brass. Head diameter 0303″. # 6 x 2″ brass flat head phillips wood screws (pack of 12).
# 5 X 3/4″ Brass Flat Head Phillips Wood Screws (Box of 100) - Screws. # 5 x 3/4″ brass flat head phillips wood screws (box of 100). Business and industrial. Fasteners and hardware.
100 Piece No.5 Brass Wood Screws 5/8″ Flathead Slotted - #5 x 5/8″ great for small crafts and woodworking. Slotted head ideal for authentic restoration work. Solid brass construction good for exterior use.
#6 x 5/8″ Slotted Round Head Solid Brass Wood Screw Qty 500 - Austentic, refers to 300 series stainless, the most popular of the stainless alloys accounting for 85%-90% of stainless fasteners soldnamed for sir robert williams austen, an english metallurgist, austentic stainless is a crystal structure formed by heating steel, chromium, and nickel to a high temperature where it forms the characteristics of 300 series stainless steel. Tensile strength, a common measure to compare the strength of a fastener. Screw body size#6 (0. The term “18-8″ is used interchangeably to characterize fasteners made of 302,302hq,303,304,384, xm7, and other variables of these grades with close chemical compositions. It is the load needed to pull the fastener apart. The chromium protects the iron against most corrosion or red colored rust thus the term “stainless steel”. 138″)body length5/8″drive typeslottedhead styleround headmaterialsolid brasstensile strength50,000, 65,000 psidrive styleslottedhardness40-75 rockwell b min. There is little overall difference in corrosion resistance among the 18-8 types, but slight differences in chemical composition do make certain grades more resistant than others against particular chemicals or atmospheres. The ability of stainless to form a thin layer of protection on its outside surface, called a “passive film”, is its most important characteristic in preventing corrosion. Yield30,000, 50,000 psipackage quantity500 common fastener label definitions”stainless steel”, with the addition of 12% chromium to iron, stainless steel is formed. Yield, the resistance to a load pulling on the middle of a fastener until the fastener shows permanent deformation. “18-8″, 300 series stainless steel having approximately (not exactly) 18% chromium and 8% nickel.
100 Piece Dark Finish No.5 Brass Wood Screws 5/8″ Flathead Phillips - Solid brass construction good for exterior use. #5 x 5/8″ great for small crafts and woodworking. Oil rubbed bronze finish adds an authentic look.
Brass Wood Screw, Plain Finish, Flat Head, Slotted Drive, 1/4″ Length, #2 Threads (Pack of 100) - Length is measured from the top of the head. Flat head fasteners are designed to fit flush to the surface when used with countersunk holes. Common applications for slotted screws include woodworking, although the drive style is not designed to be used with power drivers. Threads specially designed for use in wood effectively resist pulling out. Wood screws are designed to attach two pieces of wood together. The typical composition is 70% copper and 30% zinc. Strength increases with a higher percentage of zinc. They generally feature a smooth, unthreaded shank below the head which ensures a tight attachment, and the threaded portion of the shank is tapered to increase the holding power. Brass is rust proof, corrosion resistant and polishes to a rich, golden color. Brass is easily soldered and brazed and accepts plating readily.
#8×3″ PHIL FLAT HEAD Brass Wood Screw (100/box) - Material alloy(cadmium free). Colorbronze tone. Please choose the size that you want from the dropdown menu above.
#14 x 3/4″ Solid Brass Round Head Wood Screw Qty 50 Pieces, Slotted Drive, Number 14 Size x 3/4″ Length - A screw designed for a wood or a similar material, with a point, a relatively coarse thread, a thick shank, and, usually, an unthreaded portion of the shank at the head end. .
Crown Bolt 23572 #10 x 2 Inch Flat-Head Phillips Brass Wood Screws, 50-Count - For general applications. Brass finish. 2-inch fastener length. #10 body diameter. Brass #10 x 2 inch wood screws flat head phillips.
#4 x 1-1/4″ Slotted Oval Head Solid Brass Wood Screw Qty 100 - It is the load needed to pull the fastener apart. “18-8″, 300 series stainless steel having approximately (not exactly) 18% chromium and 8% nickel. Yield, the resistance to a load pulling on the middle of a fastener until the fastener shows permanent deformation. The chromium protects the iron against most corrosion or red colored rust thus the term “stainless steel”. The term “18-8″ is used interchangeably to characterize fasteners made of 302,302hq,303,304,384, xm7, and other variables of these grades with close chemical compositions. Tensile strength, a common measure to compare the strength of a fastener. There is little overall difference in corrosion resistance among the 18-8 types, but slight differences in chemical composition do make certain grades more resistant than others against particular chemicals or atmospheres. Screw body size#4 (0. 112″)body length1-1/4″drive typeslottedhead styleoval headmaterialsolid brasstensile strength50,000, 65,000 psidrive styleslottedhardness40-75 rockwell b min. Yield30,000, 50,000 psipackage quantity100 common fastener label definitions”stainless steel”, with the addition of 12% chromium to iron, stainless steel is formed. The ability of stainless to form a thin layer of protection on its outside surface, called a “passive film”, is its most important characteristic in preventing corrosion. Austentic, refers to 300 series stainless, the most popular of the stainless alloys accounting for 85%-90% of stainless fasteners soldnamed for sir robert williams austen, an english metallurgist, austentic stainless is a crystal structure formed by heating steel, chromium, and nickel to a high temperature where it forms the characteristics of 300 series stainless steel.
Brass Wood Screw, Plain Finish, Round Head, Phillips Drive, 3/8″ Length, #5 Threads (Pack of 100) - Strength increases with a higher percentage of zinc. The typical composition is 70% copper and 30% zinc. Brass is rust proof, corrosion resistant and polishes to a rich, golden color. Round head fasteners have a dome-shaped head. An older style of head, it is typically used when replacing existing round-head fasteners where an exact match is desired. Threads specially designed for use in wood effectively resist pulling out. They generally feature a smooth, unthreaded shank below the head which ensures a tight attachment, and the threaded portion of the shank is tapered to increase the holding power. The phillips drive style was originally designed so that the driver would slip out under extreme torque, preventing over-tightening and damage to the fastener or the material. Wood screws are designed to attach two pieces of wood together. Brass is easily soldered and brazed and accepts plating readily.
#2×3/4″ PHIL FLAT HEAD Brass Wood Screw (100/box) - Head diameter 0303″. Screws, solid brass. Head height 0123″. # 6 x 2″ brass flat head phillips wood screws (pack of 12). Tensile strength 50,000, 60,000 psi.
#5 x 1″ Solid Brass Round Head Wood Screw Qty 100 Pieces, Slotted Drive, Number 5 Size x 1″ Length - A screw designed for a wood or a similar material, with a point, a relatively coarse thread, a thick shank, and, usually, an unthreaded portion of the shank at the head end. .
#1 x 1/4″ Slotted Round Head Solid Brass Wood Screw Qty 100 - Tensile strength, a common measure to compare the strength of a fastener. It is the load needed to pull the fastener apart. 073″)body length1/4″drive typeslottedhead styleround headmaterialsolid brasstensile strength50,000, 65,000 psidrive styleslottedhardness40-75 rockwell b min. Yield30,000, 50,000 psipackage quantity100 common fastener label definitions”stainless steel”, with the addition of 12% chromium to iron, stainless steel is formed. The ability of stainless to form a thin layer of protection on its outside surface, called a “passive film”, is its most important characteristic in preventing corrosion. Yield, the resistance to a load pulling on the middle of a fastener until the fastener shows permanent deformation. “18-8″, 300 series stainless steel having approximately (not exactly) 18% chromium and 8% nickel. The chromium protects the iron against most corrosion or red colored rust thus the term “stainless steel”. There is little overall difference in corrosion resistance among the 18-8 types, but slight differences in chemical composition do make certain grades more resistant than others against particular chemicals or atmospheres. Austentic, refers to 300 series stainless, the most popular of the stainless alloys accounting for 85%-90% of stainless fasteners soldnamed for sir robert williams austen, an english metallurgist, austentic stainless is a crystal structure formed by heating steel, chromium, and nickel to a high temperature where it forms the characteristics of 300 series stainless steel. Screw body size#1 (0. The term “18-8″ is used interchangeably to characterize fasteners made of 302,302hq,303,304,384, xm7, and other variables of these grades with close chemical compositions.
#14 x 2″ Solid Brass Round Head Wood Screw Qty 50 Pieces, Slotted Drive, Number 14 Size x 2″ Length - . A screw designed for a wood or a similar material, with a point, a relatively coarse thread, a thick shank, and, usually, an unthreaded portion of the shank at the head end.
We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.