OKSLO Disston G044 Remgrit 2.75 in. Carbide Grit Hole Saw
- 5 hole-saws (1-1/4″, 2-1/8″, 2-5/8″, 2-7/8″, 3-1/4″). Will cut through ceramic, plastic, fiberboard, fiberglass, concrete bock, and plywood a must have too for cutting standard faucet and shower head pipe holes in tile the case may be damaged or cracked during shipping. Fit on drill 500rpm, driver depth 55mm. Self sharpening hole saw for long time use. Included locating plate pilot drill file 10″ (250mm).
Disston GO24 38mm Carbide Grit Holesaw by Disston
- Proudly made in usa. Please see the specifications in the table below for full details if you have any questions or doubts, or if your requirements include specific dimensions, please contact us prior to placing your order. Pictures are representative of item, but are not of the actual item product dimensions, finish, head markings, thread length, stamping shape or forging shape, etc, may differ from picture products are guaranteed to meet the specifications to which they are manufactured specifications allow for tolerances in dimension and shape, which can vary from lot to lot. All asmc industrial fasteners are guaranteed to be of the highest quality and are fully traceable and lot-controlled. Asmc industrial offers a comprehensive selection industrial, automotive, and construction fasteners our parts are high-quality, at low prices, shipped from stock we also feature a full line of usa-made fasteners, including grade 5 and grade 8 hex cap screws, sockets, stainless products, nuts, and washers.
Moon Daughter Pro 8pc Tungsten Carbide Grit Hole Saws Cutter Masonry Ceramic Plastic Fiberboar
- Self sharpening hole saw for long time use will cut through ceramic, plastic, fiberboard, fiberglass, concrete bock, and plywood a must have too for cutting standard faucet and shower head pipe holes in tile.
Century Drill & Tool 5507 3/8″ Carbide Grit Hole Saw Pilot Drill Bit
- 3/8-inch hex shank. Fits f and g arbors. Tungsten carbide tipped pilot drill.
Tungsten Carbide Grit Holesaw 103mm Tungsten carbide grit cutting edge
- Tungsten carbide grit cuts through fiberglass, ceramic tile, laminates and other abrasive materials carbide grit edge will not snag or chip when cutting thin materials. 1-3/4″ carbide grit holesaw diameter 1-3/4″ depth of cut approximately 1-1/2″ for pipe tap 1-1/2″ for pipe entrance 1-1/4″ use with lenox 2l arbor (len2l), replacing standard pilot drill bit with carbide pilot drill bit.
Disston GO32 51mm Carbide Grit Holesaw by Disston
- All asmc industrial fasteners are guaranteed to be of the highest quality and are fully traceable and lot-controlled. Asmc industrial offers a comprehensive selection industrial, automotive, and construction fasteners our parts are high-quality, at low prices, shipped from stock we also feature a full line of usa-made fasteners, including grade 5 and grade 8 hex cap screws, sockets, stainless products, nuts, and washers. Proudly made in usa. Pictures are representative of item, but are not of the actual item product dimensions, finish, head markings, thread length, stamping shape or forging shape, etc, may differ from picture products are guaranteed to meet the specifications to which they are manufactured specifications allow for tolerances in dimension and shape, which can vary from lot to lot. Please see the specifications in the table below for full details if you have any questions or doubts, or if your requirements include specific dimensions, please contact us prior to placing your order.
Greenlee 725-3-5/8 Carbide-Grit Hole Saw, 3-5/8-Inch by Greenlee
- 2-1/4″ cutting depth 3/8″ shank. For use on concrete block, cultured marble, brick, cement board, wood, drywall, pvc, fiberglass, ceramic tile, plastic, plexiglass. Cuts clean holes smoothly in materials without snagging designed to work with any variable speed hand drill. Tungsten carbide grit hole saw set for abrasive construction materials set includes 1 ea 1-1/4″, 2-1/8″, 2-5/8, 2-7/8″, 3-1/4″, small mandrel, pilot bit & storage case. For the builder, tile setter, homeowner, do-it-yourselfer, construction worker and other professionals.
Tungsten Carbide Grit Holesaw 73mm Tungsten carbide grit cutting edge
- 1-3/4″ carbide grit holesaw diameter 1-3/4″ depth of cut approximately 1-1/2″ for pipe tap 1-1/2″ for pipe entrance 1-1/4″ use with lenox 2l arbor (len2l), replacing standard pilot drill bit with carbide pilot drill bit. Tungsten carbide grit cuts through fiberglass, ceramic tile, laminates and other abrasive materials carbide grit edge will not snag or chip when cutting thin materials.
Unik Always 8pieces Tungsten Carbide Grit Hole Saw Cutter Kit Masonry ceramic plastic fiberboard
- Self sharpening hole saw for long time use. Will cut through ceramic, plastic, fiberboard, fiberglass, concrete bock, and plywood. A must have too for cutting standard faucet and shower head pipe holes in tile. The case may be damaged or cracked during shipping.
MAGBIT 625.3416 MAG625 2-1/8-Inch Carbide Grit Hole Saw with 1-9/16-Inch Depth
- 1-3/8-inch depth. Drilling a hole through concrete block takes less than 7 seconds. Works in rotary and sds hammer mode, works forward and reverse. Use standard or sds shank arbors. Cuts brick, concrete block, fiber cement siding & backer board, stucco, old plaster.
Tungsten Carbide Grit Holesaw 43mm Tungsten carbide grit cutting edge
- Tungsten carbide grit cuts through fiberglass, ceramic tile, laminates and other abrasive materials carbide grit edge will not snag or chip when cutting thin materials. 1-3/4″ carbide grit holesaw diameter 1-3/4″ depth of cut approximately 1-1/2″ for pipe tap 1-1/2″ for pipe entrance 1-1/4″ use with lenox 2l arbor (len2l), replacing standard pilot drill bit with carbide pilot drill bit.
ExpertStores 8pc Tungsten Carbide Grit Hole Saws Cutter Masonry Pro With Case
- 8pc tungsten-carbide grit hole saws specification this industrial quality hole saws kit is designed for you to cuts clean, smooth, and accurate holes in many types of hard materials. These saws can be able to cut/drill through bricks, masonry, ceramic tiles, & concrete blocks up to 2″ thick they are made by machined carbon steel with c2 tungsten carbide grit cutting surfaces. Features provides easily through-hole drilling fits on most electric drills with min. 500rpm driver depth 55mm perfect for bricks, ceramic tiles, masonry, concrete blocks includes 1 aluminum plate 1 center drill 1 half-round file 5 hole saws mm & sae 33mm(1-5/16″) 53mm(2-1/16″) 67mm(2-5/8″) 73mm(2-7/8″) 83mm(3-1/4″).
8 Pcs Tungsten Carbide Grit Hole Saw Kit Masonry Tile
- Designed for you to cuts clean smooth and accurate holes in many types of hard materials. 8pc tungsten-carbide grit hole saws specification this industrial quality hole saws kit is. Blocks up to 2 thick they are made by machined carbon steel with c2 tungsten carbide”. These saws can be able to cut/drill through bricks masonry ceramic tiles & concrete. Grit cutting surfaces features provides easily through-hole drilling fits on most elec.
Lenox Tools 2992424CG Master-Grit Carbide Grit Hole Saw, 1-1/2-Inch or 38mm
- Tungsten carbide grit cutting edge. Ideal for cutting abrasive materials. Clean cutting through thin materials.
MAGBIT 625.2816 MAG625 1-3/4-Inch Carbide Grit Hole Saw with 1-9/16-Inch Depth
- Cuts brick, concrete block, fiber cement siding & backer board, stucco, old plaster. Drilling a hole through concrete block takes less than 7 seconds. Works in rotary and sds hammer mode, works forward and reverse. Use standard or sds shank arbors. 1-3/8-inch depth.
LENOX Tools Hole Saw, Carbide Grit, 4-Inch or 102mm (2996464CG)
- Hole saw has a clean-cutting carbide grit edge that won’t snag or chip when cutting thin materials. Heat resistant carbide teeth for long life in tile and stainless steel. Carbide grit hole saw cuts through a wide range of abrasive materials. 4-inch diameter. Use the hole saw with a 2l or 7l standard arbor or a 2l snap-back arbor.
MAGBIT 625.2216 MAG625 1-3/8-Inch Carbide Grit Hole Saw with 1-9/16-Inch Depth
- Use standard or sds shank arbors. Drilling a hole through concrete block takes less than 7 seconds. Cuts brick, concrete block, fiber cement siding & backer board, stucco, old plaster. Works in rotary and sds hammer mode, works forward and reverse. 1-3/8-inch depth.
Artu – Tungsten Carbide Grit Hole Saw, 8 PC Set
- For use on concrete block, cultured marble, brick, cement board, wood, drywall, pvc, fiberglass, ceramic tile, plastic, plexiglass. Cuts clean holes smoothly in materials without snagging designed to work with any variable speed hand drill. For the builder, tile setter, homeowner, do-it-yourselfer, construction worker and other professionals. 2-1/4″ cutting depth 3/8″ shank. Tungsten carbide grit hole saw set for abrasive construction materials set includes 1 ea 1-1/4″, 2-1/8″, 2-5/8″, 2-7/8″, 3-1/4″, small mandrel, pilot bit, tc grit file & storage case.
Blue Boar Recessed Light Carbide Grit Hole Saw 6-3/8″ dia for 6 inch lights: fast cutting in drywall, lath & plaster, Hardi board: easy plug removal uses standard 5/8 18 thread hole saw arbor adptr
- Open back design for faster cut plug removal. Attaches to standard 5/8″-18 2-pin mount hole saw arbor and works with hole pro hp1156 large shield and arbor kit. Continuous cutting edge for smooth cutting even in wood lath and plaster. 1″ deep, hard tungsten carbide grit edge for a long life in abrasive materials. Cuts through drywall, plaster, cornhole board, fiber cement hardie board, stucco, acoustical tile, ceiling tile.
We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
